The pavers finally look new again. The driveway is bright, the pool deck has its color back, and the joints are clean. Then comes the question almost every homeowner asks next: should we seal them now?
Across Windermere, Dr. Phillips, Horizon West, Winter Garden, Ocoee, and the rest of West Orlando, paver driveways and pool decks are everywhere, and sealing is one of the most common follow-up questions our crew hears after a cleaning.
The short answer: You don't have to seal pavers after a pressure wash, but a thorough cleaning is the best time to do it. Sealer deepens color, slows stains, and helps hold joint sand in place. It only works on clean, fully dry pavers free of white efflorescence haze, and it needs redoing every few years.
Do pavers actually need to be sealed?
Not structurally. The Concrete Masonry & Hardscapes Association (CMHA), in its technical guide Tech Spec 5 on cleaning, sealing, and joint sand stabilization, says sealers do not increase the structural properties of the pavers or their load capacity. Sealers are used for visual and functional reasons: they reduce how much water, stains, oil, and dirt soak into the paver surface, and they can intensify the color.
Paver makers say the same thing. Unilock, in its guide How to Seal Pavers, describes sealing as "less about maintenance and more about aesthetics," and says its concrete pavers do not require regular sealing.
So sealing is a choice, not a requirement.
Why is right after a pressure wash the best time to seal?
Because sealer locks in whatever is on the surface. CMHA's guide lists the order plainly: remove stains, remove efflorescence, clean the whole pavement, and then apply a sealer or joint sand stabilizer. It calls a newly cleaned pavement an opportune time to do it.
Seal over dirt, mildew, or an old oil spot and the sealer can trap it and make it look darker. Unilock warns that sealing over stains may accentuate them. If you have a driveway oil spot or orange irrigation stains, treat those first. Our guides on oil stains and orange sprinkler rust stains explain why those stains need their own treatment before anything else.
There is also the sand between the pavers. Pressure washing can blow joint sand out, especially with a narrow tip held too close. CMHA notes that joint sand stabilization benefits pavements that get aggressive, regular cleaning, and that liquid sealers soak into the joint sand and provide some stabilization as a side benefit. That is why a careful crew checks the joints and re-sands where needed before sealing, not after.
What does a good paver sealing job look like, step by step?
Whoever does it, the sequence matters more than the brand of sealer.
1. Clean the whole surface evenly. Our crew uses a surface cleaner for an even finish rather than a wand held close to the pavers, which can etch them and strip sand from the joints. Our guide to soft washing vs. pressure washing explains why method matters on different surfaces.
2. Treat stains and any efflorescence. Efflorescence is the chalky white haze that can appear on concrete pavers. It needs to be gone before sealing, or it can end up trapped under the sealer.
3. Refill the joints. Sweep new joint sand (often polymeric sand) into any gaps the cleaning opened up. If polymeric sand is used, it needs to cure before sealing; product makers give their own wait times on the label.
4. Let everything dry completely. Unilock says pavers in warm, sunny spots can be dry in a few hours, while shady areas need about 24 hours. Moisture trapped under sealer is a common cause of a cloudy finish.
5. Turn off the sprinklers. CMHA's guide says to turn off automatic sprinkler systems during cleaning, sealing, and drying. In a Florida yard where irrigation runs before dawn, this is the step people forget.
6. Watch the weather and the heat. Unilock recommends clear skies for 24 to 48 hours and a temperature range of roughly 50 to 90°F, and warns that sealing pavers that are too hot can cause problems. In Central Florida, that usually means avoiding the middle of a summer afternoon and keeping an eye on the daily rain pattern.
7. Apply evenly and don't let it pool. Sealer is usually sprayed and back-rolled so it does not leave puddles, streaks, or lap marks.
Wet look or natural finish: which is right?
Sealers come in different finishes. CMHA notes that some add a glossy, "wet" look and others give a low sheen or flat finish while still enhancing color. Unilock describes the same choice.
A wet look makes colors richer and is popular on driveways and entries. A natural or matte finish keeps the pavers closer to how they looked when installed. Around a pool, where people walk barefoot on wet surfaces, ask about slip resistance before choosing a glossy product, and follow the sealer maker's guidance for pool decks.
Bedrock offers wet paver sealing, which is listed on our FAQ page, and we will talk through the finish with you before any work starts.
How often should Florida pavers be resealed?
Unilock suggests resealing every three to five years for homeowners who choose to seal. In Central Florida, strong sun, frequent irrigation, afternoon storms, and daily car traffic all wear sealer, and a pool deck that is splashed and walked on daily will wear differently from a front walk.
The signs are easy to spot: color that looks faded or uneven, water that soaks in instead of beading up, and joint sand starting to wash out. When you see those, it is time to clean and reseal. Keeping the pavers on a regular cleaning schedule helps; our guide to how often to clean a Florida home exterior covers a sensible rhythm.
Should you seal brand-new pavers?
Usually not right away. New concrete pavers often show efflorescence in the first months. Unilock says to hold off on sealing until it has fully cleared, typically two to three months and sometimes up to a year. If your pavers were installed recently, check with the installer or the paver manufacturer before sealing.
What can sealer not do?
- It does not make pavers stain-proof. It slows how fast spills soak in. Oil, rust, and leaf stains still need to be wiped up quickly.
- It does not fix a sunken or shifting paver. That is a base or installation issue, not a surface one.
- It does not last forever. Plan on resealing as the finish wears.
- It does not hide a poor cleaning. Whatever is on the surface when the sealer goes on stays there.
Get an honest recommendation for your pavers
Bedrock Solutions is a trusted, locally owned, licensed exterior cleaning company serving West Orlando. Our crew cleans paver driveways, patios, walkways, and pool decks as part of our exterior cleaning services, and the Bedrock team can tell you whether sealing makes sense for your pavers or whether a good cleaning is all they need right now.
Send a few photos through our free quote form, or call or text 352-856-5018. We reply to every quote request the same day.
Frequently asked questions
Do you have to seal pavers after pressure washing?
No. Sealing is optional. Paver makers such as Unilock say their concrete pavers do not require regular sealing. A fresh, fully dry cleaning is simply the best moment to seal if you want richer color, easier cleanup, and help holding joint sand in place.
How long should pavers dry before sealing?
Until they are completely dry, surface and joints. In full Florida sun that can be a few hours; in shade, plan on about 24 hours. Sealing damp pavers can trap moisture and leave a cloudy haze under the sealer.
How often should pavers be resealed in Florida?
Unilock suggests every three to five years for owners who choose to seal. In Florida, strong sun, irrigation, and heavy use can wear sealer sooner, so watch for faded color and water that no longer beads, and follow the sealer label.
Should new pavers be sealed right away?
Usually not. Wait for efflorescence, the natural white haze on new concrete pavers, to clear first. Unilock says that typically takes two to three months and can take up to a year. Sealing over it can lock the haze in.
Will sealing make my pavers stain-proof?
No. Sealer reduces how much water, oil, and dirt soak into the pavers, which makes cleanup easier, but it does not make them stain-proof. Fresh spills still need to be wiped up quickly.